Search found 68 matches
- Sun Jan 24, 2021 4:18 pm
- Forum: MGL Radio frequency products
- Topic: Red X on V16 Com 1
- Replies: 5
- Views: 4234
Re: Red X on V16 Com 1
Did you enable COM1 in the equipment enables menu?
- Fri Jan 22, 2021 3:10 pm
- Forum: EFIS Systems
- Topic: Speedbrake (Flap) indication on EFIS
- Replies: 2
- Views: 2134
Re: Speedbrake (Flap) indication on EFIS
You could make a "gauge" in the screen designer that has this - you could also possibly use the digital input function to your advantage here. Assuming "Up" is 12V and "down" is 0V, you can have a screen design indicator that turns on and off with the digital input on the extender as an indicator li...
- Tue Jan 19, 2021 1:33 am
- Forum: General
- Topic: Deep scratch on my Explorer Lite
- Replies: 4
- Views: 4067
Re: Deep scratch on my Explorer Lite
I don't know that I would try to do anything other than live with it and try to ignore it or replace the touch screen. Especially if it's one of the newer capacitive touch displays (you'll know because there's no calibration options), adding any products to the plastic can potentially ruin the touch...
- Mon Jan 11, 2021 6:54 pm
- Forum: Technical - floobidust
- Topic: "RDAC1 fail"message on stratomaster enigma EFIS
- Replies: 3
- Views: 4135
Re: "RDAC1 fail"message on stratomaster enigma EFIS
On the back of your Enigma is a three-screw terminal block. There's +12V, Signal and Gnd. Remove the RDAC's red and braid wire and temporarily jumper them to a power and ground to see if the failure indication remains or not. If not, then individually return the power and ground back to its normal s...
- Mon Jan 11, 2021 1:42 pm
- Forum: MGL Radio frequency products
- Topic: Red X on V16 Com 1
- Replies: 5
- Views: 4234
Re: Red X on V16 Com 1
What connection did you make to the EFIS? The V16 connects to the EFIS via RS-232. Do not connect the Razor head's RS-232 or the V16 to Razor CAN Bus to the EFIS. If only the V16 is connected via RS-232, and you're sure that you have made the proper configuration selections, it is likely that you ha...
- Fri Jan 08, 2021 2:34 pm
- Forum: Technical - floobidust
- Topic: Pantalla vga
- Replies: 1
- Views: 2684
Re: Pantalla vga
Pedro,
Menores quantidades de pantallas no funcionan con el enchufe VGA.
Vaya al "Operations setup menu" a partir de "Menu" -> "System setup menu"
Localizar el selecion de "Use low noise video output timing" y cambiar a "Use standard video output timing"
Salud!
Menores quantidades de pantallas no funcionan con el enchufe VGA.
Vaya al "Operations setup menu" a partir de "Menu" -> "System setup menu"
Localizar el selecion de "Use low noise video output timing" y cambiar a "Use standard video output timing"
Salud!
- Fri Jan 08, 2021 2:22 pm
- Forum: MGL Radio frequency products
- Topic: V16 TX Interlock with a GTR200
- Replies: 4
- Views: 3456
Re: V16 TX Interlock with a GTR200
Adam, that is what I was thinking would be easiest. Shouldn't matter if I splice that at the V16 or the Audio panel end, not that it matters much. I'm already running the interlock from the gtr to the v16, can just as easily run a pair. Thanks both of you for confirming my thinking. No, it will not...
- Fri Jan 08, 2021 2:03 pm
- Forum: General
- Topic: Stratocaster enigma update
- Replies: 2
- Views: 2672
Re: Stratocaster enigma update
Enigma updates can be found at the MGL Avionics main website: http://mglavionics.co.za/EnigmaupdatesX.html
Re: Ibox
Hola!
Mi espanol es horrible, lamento los problemas gramaticales.
Tengas recepcion de GPS? El tiempo se establece en base a esto.
Mi espanol es horrible, lamento los problemas gramaticales.
Tengas recepcion de GPS? El tiempo se establece en base a esto.
- Fri Jan 08, 2021 1:54 pm
- Forum: General
- Topic: EFIS simulator
- Replies: 4
- Views: 3911
Re: EFIS simulator
Paul is right, you need to tell your EFIS to use those custom screen designs.
MENU -> System Setup Menu -> Standard system selections
Set FLIGHT or ENGINE or FUEL or INFO (depending on what you changed) to "Use custom screen designs"
Adam
MENU -> System Setup Menu -> Standard system selections
Set FLIGHT or ENGINE or FUEL or INFO (depending on what you changed) to "Use custom screen designs"
Adam