This post is directed to Rainier. Currently I have a MGL SP12 transmitting the TSO-C199 TABS protocol to a Trig TT21. Our CAA (Civil Aviation Authority) has provided a spreadsheet to me indicating that I am transmitting a SIL=1 which is not compliant. They require a SIL value of 3.
I note on the outside of the SP12 it indicates a SIL value of 3.
When I read the corresponding Trig information regarding the Trig TN72 (SP12 equivalent) it states the following when the TN72 is interfaced to Trig TT21/22
C199 TABSTransponder sends ADS-B data in accordance with TSO C199; SIL = 1, SDA = 1.
Trig TN72 SIL 3Transponder sends ADS-B data in accordance with FAR 91.227; SIL = 3, SDA = 2.
So how do I get my MGL SP12 or Trig TT21 to comply with the FAR 91.227 and provide values of SIL=3 and SDA=2
In reading the Trig Documentation I note;
GPS CertificationLevel
If you are using the TN72 as a simple NMEA GPS source, it should be set to uncertified. When a C199 TABS GPS source is selected the certification level is not used by the Trig transponder; TSO-C199 uses a special encoding of the design assurance flags. When compliance with FAR 91.227 is being configured, the GPS certification level can be set to level C.
From this I take it that I need to set the GPS certification level in my Trig TT21 but then what input do I use for FAR 91.227 compliance.
Appreciate your help so I can comply.
Thanks Peter
MGL SP12 correct SIL output
Forum rules
Please keep your posts friendly and on topic. No politics or discussions of a controversial nature not related to our favorite subject of flying and avionics. Offending posts may be removed or moderated.
Please keep your posts friendly and on topic. No politics or discussions of a controversial nature not related to our favorite subject of flying and avionics. Offending posts may be removed or moderated.
MGL SP12 correct SIL output
Peter Armstrong
DynAero MCR-4S ZK-PSA
Auckland New Zealand
2 x G2 Voyagers, Extreme, 3 MGL Servos, SP2, SP4, SP6, SP7, 2 x V10's, MGL SP12, RDAC, I/O Extender
DynAero MCR-4S ZK-PSA
Auckland New Zealand
2 x G2 Voyagers, Extreme, 3 MGL Servos, SP2, SP4, SP6, SP7, 2 x V10's, MGL SP12, RDAC, I/O Extender
Re: MGL SP12 correct SIL output
If you are transmitting SIL=1 it means you are transmitting the GPS information from the built in GPS of the iEFIS which is qualified to SIL=1.
Have a look at the dedicated diagnostics page provided on the iEFIS for this.
The Trig transponder interface receives both the SP-12 as well as the iEFIS GPS position. if there is no valid position from the SP-12 it will use the position from the iEFIS and SIL/SDA are both set accordingly.
There is more info on how this all fits together in the SP-12 manual.
If you are using an iBOX - make sure your SP-12 and the trig interface are on the same CAN bus. The SP-12 GPS information goes straight to the trig without touching the EFIS in order to maintain SIL/SDA.
Have a look at the dedicated diagnostics page provided on the iEFIS for this.
The Trig transponder interface receives both the SP-12 as well as the iEFIS GPS position. if there is no valid position from the SP-12 it will use the position from the iEFIS and SIL/SDA are both set accordingly.
There is more info on how this all fits together in the SP-12 manual.
If you are using an iBOX - make sure your SP-12 and the trig interface are on the same CAN bus. The SP-12 GPS information goes straight to the trig without touching the EFIS in order to maintain SIL/SDA.