I also have the same problem as VA Long Ez, maybe this question is for Rainier..
Is there anyone looking into fixing the 1.1.2 version as it is required to install the Wifi gateway???
Regards..
Search found 29 matches
- Wed Dec 14, 2022 11:00 am
- Forum: EFIS Systems
- Topic: Odd EFIS problem
- Replies: 19
- Views: 7742
- Mon Dec 12, 2022 8:17 pm
- Forum: Technical - floobidust
- Topic: RDAC XF MAP software update...
- Replies: 1
- Views: 4499
RDAC XF MAP software update...
After updating my G3 Challenger to the latest update, I went on to update the RDAC. Pretty sure the update didn't go to the 100% mark and now all my sensors CHT/EGT etc have a big red X on them. Went in diagnostic and my RDAC is not connected and the LED on RDAC is solid. Nothing else was done but t...
- Mon Dec 12, 2022 7:16 pm
- Forum: Technical - floobidust
- Topic: Problem with RDAC XF MAP
- Replies: 1
- Views: 5376
Re: Problem with RDAC XF MAP
Jay..
Did you ever got it to work again??????
Just did a software update to it and i'm experiencing the same thing as you are..
Regards
Did you ever got it to work again??????
Just did a software update to it and i'm experiencing the same thing as you are..
Regards
- Fri Dec 09, 2022 8:58 pm
- Forum: MGL Radio frequency products
- Topic: VSWR on V16
- Replies: 2
- Views: 5012
Re: VSWR on V16
Rainier..
You were right, my battery was down to 12V.
Regards
Michel
You were right, my battery was down to 12V.
Regards
Michel
- Fri Dec 09, 2022 12:12 pm
- Forum: MGL Radio frequency products
- Topic: VSWR on V16
- Replies: 2
- Views: 5012
VSWR on V16
So here it is.... I have cut my coax for 126.700 Mhz and must of done a good job as it is showing 1.0 for VSWR. If I check at either 118.000 Mhz or 134.00 Mhz I get 1.2 for VSWR. So far so good, I have noticed that at that VSWR (1.0) it's outputting around 5 watts, and for the other freq. at VSWR 1....
- Wed Dec 07, 2022 12:24 pm
- Forum: Technical - floobidust
- Topic: RS232 NMEA output
- Replies: 1
- Views: 1577
RS232 NMEA output
Trying to find out... if from my Challenger with Extender, if the serial port once assign as a GPS NMEA port It will be able to connect to my TRIO head to drive the Autopilot???? :roll: :roll: I presently have an iFLYGPS 740 that send NMEA 0183 sentence that drive the autopilot but I would like to b...
- Mon Nov 28, 2022 1:19 pm
- Forum: MGL Radio frequency products
- Topic: V16 Power
- Replies: 2
- Views: 4534
Re: V16 Power
OK thank you.
I'm using a DB25 to do my wiring connection and somehow the Pin 23(gnd) on board was faulty,
the foil on the PCB board was cut/scratched so no ground. I have used Pin 22 which is interconnected.
What a relief as I thought I had scrapped the V16 somehow.
I'm using a DB25 to do my wiring connection and somehow the Pin 23(gnd) on board was faulty,
the foil on the PCB board was cut/scratched so no ground. I have used Pin 22 which is interconnected.
![Very Happy :D](./images/smilies/icon_e_biggrin.gif)
![Very Happy :D](./images/smilies/icon_e_biggrin.gif)
What a relief as I thought I had scrapped the V16 somehow.
- Sun Nov 27, 2022 4:41 pm
- Forum: MGL Radio frequency products
- Topic: V16 Power
- Replies: 2
- Views: 4534
V16 Power
Hi Folks...
When power is applied, should the LED light-up?????
SHould the LED blink once a connection is established to the Razor head?????
Regards
When power is applied, should the LED light-up?????
SHould the LED blink once a connection is established to the Razor head?????
Regards
- Sat Nov 26, 2022 9:54 am
- Forum: EFIS Systems
- Topic: Design/simulator 1.1.2.2
- Replies: 5
- Views: 2045
Re: Design/simulator 1.1.2.2
Yep that was it... Thx
![Idea :idea:](./images/smilies/icon_idea.gif)
![Idea :idea:](./images/smilies/icon_idea.gif)
![Idea :idea:](./images/smilies/icon_idea.gif)
- Thu Nov 17, 2022 2:45 pm
- Forum: EFIS Systems
- Topic: Design/simulator 1.1.2.2
- Replies: 5
- Views: 2045
Re: Design/simulator 1.1.2.2
Bill.
If you don't mind and maybe missing the obvious, On the simulator my speed indicates 251 which stop me
to have access to certain option.
Can you give me a hint on where I can set it to zero????
Regards
If you don't mind and maybe missing the obvious, On the simulator my speed indicates 251 which stop me
to have access to certain option.
Can you give me a hint on where I can set it to zero????
Regards