Search found 13 matches
- Wed May 22, 2024 2:00 pm
- Forum: EFIS Systems
- Topic: Enigma error messages
- Replies: 3
- Views: 254
Re: Enigma error messages
As addition infor, the unit did work for one day, before this error happened. I did look for whiskers with about 100x magnification. And did found clearly one such. Opened that with scalper. Also checked the other 200'ish legs. And cleaned suspicious. Blown any chips clear of the board. But starting...
- Fri Apr 26, 2024 7:53 am
- Forum: EFIS Systems
- Topic: Enigma error messages
- Replies: 3
- Views: 254
Enigma error messages
is there somewhere list of error messages, and what they mean?
While starting an unit that has been long in storage, it says
"Cannot deermine Flash type"
and stops.
While starting an unit that has been long in storage, it says
"Cannot deermine Flash type"
and stops.
- Fri Feb 09, 2024 9:22 am
- Forum: Technical - floobidust
- Topic: NTC expected voltage readings (Carb Temp)
- Replies: 6
- Views: 4435
Re: NTC expected voltage readings (Carb Temp)
can be same, or not
Having difficulties to get carb temperature to work properly.
It shows temperatures, but the minimum temperature is 20 deg C!
And for carb temp the interesting temperature is lower, near zero.
Or is the problem with the sensor (picture)?
Having difficulties to get carb temperature to work properly.
It shows temperatures, but the minimum temperature is 20 deg C!
And for carb temp the interesting temperature is lower, near zero.
Or is the problem with the sensor (picture)?
- Sat Jun 17, 2023 5:22 am
- Forum: EFIS Systems
- Topic: iEFIS Discovery Lite plus RDAC XF MAP
- Replies: 0
- Views: 13813
iEFIS Discovery Lite plus RDAC XF MAP
Ideas what is the problem; this is what Erkki told me: Setup is like this iEFIS Discovery Lite - RDAC XF MAP - SP6, - SP7 I tried to modify the pages, especially the engine. I made some stupid mistake and completely lost a block of fuel (mainly fuel pressure is necessary), so I did a full boot on th...
- Mon Jun 13, 2022 8:24 am
- Forum: EFIS Systems
- Topic: iEFIS and RDAC
- Replies: 5
- Views: 1600
Re: iEFIS and RDAC
order of boxes (from iEFIS) in CAN line
- RDAC
- SP7
-SP6
- RDAC
- SP7
-SP6
- Sat Jun 11, 2022 5:04 am
- Forum: EFIS Systems
- Topic: iEFIS and RDAC
- Replies: 5
- Views: 1600
Re: iEFIS and RDAC
Yes
RDAC shows green flash at about once a second.
SP6 and SP7 double flash. And their signal is working in EFIS.
Termination resistor (120 ohm) is at both ends of the CAN.
Removing SP7 from line does not affect RDAC:
RDAC shows green flash at about once a second.
SP6 and SP7 double flash. And their signal is working in EFIS.
Termination resistor (120 ohm) is at both ends of the CAN.
Removing SP7 from line does not affect RDAC:
- Fri Jun 10, 2022 9:43 am
- Forum: EFIS Systems
- Topic: iEFIS and RDAC
- Replies: 5
- Views: 1600
iEFIS and RDAC
Setup is like this iEFIS Discovery Lite - RDAC XF MAP - SP6 - SP7 SP6 and SP7 are detected and they flash double flashes. for RDAC EFIS says "Rdac not available" and in info "Rdac not connected". Tried with two different RDAC:s, same results. CAN wires shorthened. iEFIS firmware updated. ideas!!
- Tue Mar 29, 2022 4:31 am
- Forum: The MGL/Infinitec Singles
- Topic: INFO1 g limits
- Replies: 2
- Views: 1904
Re: INFO1 g limits
thanks, waiting for it. This aerobatic aeroplane g-limits are +/- 10 g . It would be nice to have that fully supported. This would be a wonder intrument for all aerobatic aeroplanes, if scale allows that. So that -6g is far too little. It looks that the instrument has measuring range to +/-16 g. For...
- Thu Mar 24, 2022 6:48 am
- Forum: The MGL/Infinitec Singles
- Topic: INFO1 g limits
- Replies: 2
- Views: 1904
INFO1 g limits
Of the g measurements Selected first suitable scale +10 g / -8 g setting NEG HIGH limit to -9 g. I assumed that the red limit should be set in analog scale to -9 g. This does not happen, the red limit stays in -3 g! tested this by setting NEG HIGH with small steps and it looks like, that -6 g is the...
- Wed Jan 19, 2022 7:06 am
- Forum: EFIS Systems
- Topic: MX1 orientation
- Replies: 3
- Views: 1916
MX1 orientation
I have seen pictures where MX1 is installed horizontally, so that knobs are on the right side.
Is it possible to install it horizontally so that knobs are on the LEFT side?
Is it possible to install it horizontally so that knobs are on the LEFT side?