Hi Josh
I think you upgraded from a very old version. Write down your important settings and then load default settings. This will make it like a new unit from the factory. This should sort out the issue.
Regards,
Franz
Search found 39 matches
- Mon Mar 28, 2022 10:37 am
- Forum: EFIS Systems
- Topic: MGL Avionic XTreme - COMPASS SETUP - Crash FW
- Replies: 2
- Views: 1912
- Mon Mar 28, 2022 5:18 am
- Forum: The MGL/Infinitec Singles
- Topic: INFO1 g limits
- Replies: 2
- Views: 2273
Re: INFO1 g limits
Hi Aki,
Yes, the +10G/-8G alarm lower limit is max -6G. I will change it in a future software release to -8G.
Regards,
Franz
Yes, the +10G/-8G alarm lower limit is max -6G. I will change it in a future software release to -8G.
Regards,
Franz
- Fri May 14, 2021 4:33 pm
- Forum: General
- Topic: CHT and Oiltemperature sensors issur
- Replies: 3
- Views: 5439
Re: CHT and Oiltemperature sensors issur
Hi Christoph,
Is this the Xtreme-EMS or EFIS unit? What firmware are you running?
Regards,
Franz
Is this the Xtreme-EMS or EFIS unit? What firmware are you running?
Regards,
Franz
- Mon Apr 19, 2021 11:56 am
- Forum: General
- Topic: Xtreme EMS 912iS issues
- Replies: 3
- Views: 5313
Re: Xtreme EMS 912iS issues
Hi Ken,
We have recently upgraded the Xtreme-EMS code. Sounds like some gremlins are attacking. Please PM me your address and I will send you some firmware to try out.
Regards,
Franz
We have recently upgraded the Xtreme-EMS code. Sounds like some gremlins are attacking. Please PM me your address and I will send you some firmware to try out.
Regards,
Franz
- Fri Dec 11, 2020 8:31 am
- Forum: The MGL/Infinitec Singles
- Topic: FF-4 Mixed data sources?
- Replies: 2
- Views: 4125
Re: FF-4 Mixed data sources?
The FF-4 data can either be from the RDAC or from the internal electronics. It can be from both sources.
Regards,
Franz
Regards,
Franz
- Mon Nov 23, 2020 8:08 am
- Forum: EFIS Systems
- Topic: Xtreme EFIS default page
- Replies: 2
- Views: 2540
Re: Xtreme EFIS default page
Hi Steve,
The Xtreme does remember the last page you were on before power off. Your internal CR2032 battery is flat, please replace and give it a try.
Regards,
Franz
The Xtreme does remember the last page you were on before power off. Your internal CR2032 battery is flat, please replace and give it a try.
Regards,
Franz
- Fri Oct 23, 2020 3:22 pm
- Forum: The MGL/Infinitec Singles
- Topic: Data logger LOG-1
- Replies: 5
- Views: 5833
Re: Data logger LOG-1
Hi Aki,
All Vega and Blaze units have a RS232 port. Upgraded code to enable the serial output was completed a few months ago.
Regards,
Franz
All Vega and Blaze units have a RS232 port. Upgraded code to enable the serial output was completed a few months ago.
Regards,
Franz
- Wed Oct 21, 2020 3:14 pm
- Forum: The MGL/Infinitec Singles
- Topic: Data logger LOG-1
- Replies: 5
- Views: 5833
Re: Data logger LOG-1
Hi Aki,
The LOG-1 will write the attitude data 10 times a second but the logged time is only in seconds, meaning you will get 10 values of attitude data per logged second.
Regards,
Franz
The LOG-1 will write the attitude data 10 times a second but the logged time is only in seconds, meaning you will get 10 values of attitude data per logged second.
Regards,
Franz
- Fri Oct 02, 2020 10:05 am
- Forum: EFIS Systems
- Topic: FuelP issue on Gen 1 Xtreme EFIS
- Replies: 2
- Views: 2884
Re: FuelP issue on Gen 1 Xtreme EFIS
Hi Ken,
The fuel pressure is only available when using the CAN bus interface. The CAN bus is recommended as it is more reliable.
Regards,
Franz
The fuel pressure is only available when using the CAN bus interface. The CAN bus is recommended as it is more reliable.
Regards,
Franz