Search found 39 matches
- Mon Jul 15, 2024 5:16 pm
- Forum: EFIS Systems
- Topic: XTreme EMS G2 GPS and Time problems
- Replies: 6
- Views: 1340
Re: XTreme EMS G2 GPS and Time problems
Hi Steve, You need to send the GGA message so the Xtreme knows what fix it is. Once a 3d fix is obtained then the gps altitude will be displayed. You are sending conflicting GSA messages: $GPGSA,A,3,02,05,07,08,09,13,14,17,20,21,22,30,1.0,0.5,0.8,1*21 $GPGSA,A,3,11,12,23,39,40,43,,,,,,,1.0,0.5,0.8,4...
- Mon Jul 08, 2024 11:51 am
- Forum: EFIS Systems
- Topic: XTreme EMS G2 GPS and Time problems
- Replies: 6
- Views: 1340
Re: XTreme EMS G2 GPS and Time problems
Hi Steve, Thanks for posting the GPS data - it helped a lot. We have updated the GPS sentences to include the GN sentences. The EMS was only looking for GPS messages and I seen you are using a gps receiver that includes the BeiDou satellites Code has been uploaded - version 2.17 Let me know how it g...
- Thu Jun 20, 2024 8:46 am
- Forum: EFIS Systems
- Topic: G-Force setup issue
- Replies: 3
- Views: 397
Re: G-Force setup issue
Xtreme EFIS Version 3.11 has been uploaded.
https://www.mglavionics.co.za/xtreme.html
Regards,
Franz
https://www.mglavionics.co.za/xtreme.html
Regards,
Franz
- Tue Jun 18, 2024 2:42 pm
- Forum: EFIS Systems
- Topic: Xtreme EMS Gps Antenna
- Replies: 1
- Views: 254
Re: Xtreme EMS Gps Antenna
Hi Spooby, You can connect the Garmin G5 RS232 Tx and RS232 ground to the Xtreme EMS Port 2 Rs232 Rx and ground. (Setup the garmin and Xtreme accordingly eg Baud rate) Any external GPS receiver that is capable of RS232 NMEA out can be connected to the Xtreme EMS. You cannot just cut of the connector...
- Tue Jun 18, 2024 2:25 pm
- Forum: EFIS Systems
- Topic: G-Force setup issue
- Replies: 3
- Views: 397
Re: G-Force setup issue
Hi Iroazh,
Yes, you are correct. Thanks for bringing this to our attention. The negative Alarm/high items are swapped. We will fix this in the next day or so.
You can find the firmware revision in the MISC SETUP->INFORMATION.
Reagrds,
Franz
Yes, you are correct. Thanks for bringing this to our attention. The negative Alarm/high items are swapped. We will fix this in the next day or so.
You can find the firmware revision in the MISC SETUP->INFORMATION.
Reagrds,
Franz
- Tue Jun 18, 2024 1:50 pm
- Forum: EFIS Systems
- Topic: XTreme EMS G2 GPS and Time problems
- Replies: 6
- Views: 1340
Re: XTreme EMS G2 GPS and Time problems
Hi Steve, I had a look at the photos. Just a few things to check. 1) Please upgrade to the latest firmware (Version 2.16) 2) You are still transmitting the GPGSV message as the skyview and signal quality is still shown. 3) You can change the baud rate of the GPS receiver under the GPS setup. 4) I do...
- Tue Jun 18, 2024 1:37 pm
- Forum: EFIS Systems
- Topic: Xtreme EMS display not working correctly
- Replies: 3
- Views: 11933
Re: Xtreme EMS display not working correctly
Hi This is a bug in the Garmin Aera 660 where the Garmin is outputting 0 for the signal to noise ratio. See below. Regards, Franz Data capture from Garmin Aero 660 $GPGSV,3,1,12,03,05,035,00,06,73,020,00,11,61,234,00,12,28,317,00*76 $GPGSV,3,2,12,17,30,068,00,19,50,043,00,22,43,131,00,24,28,260,00*7...
- Thu May 16, 2024 4:44 am
- Forum: General
- Topic: Xtreme EMS
- Replies: 10
- Views: 1324
Re: Xtreme EMS
Hi Mike, Regarding the fuel flow. Select the fuel mode: differential or summation. You should be seeing some current (as long as it is a few amps). You could do into the Sensor info menu on the Xtreme and see if there is any change in the Current ADC value. Then you will know if the current sensor i...
- Wed May 08, 2024 11:18 am
- Forum: EFIS Systems
- Topic: XTreme EFIS-G3 - frozen display
- Replies: 4
- Views: 1257
Re: XTreme EFIS-G3 - frozen display
Hi Moshe,
Please load V3.10. We have identified an issue which might be causing your problem.
Regards,
Franz
Please load V3.10. We have identified an issue which might be causing your problem.
Regards,
Franz
- Mon Feb 12, 2024 6:41 pm
- Forum: EFIS Systems
- Topic: XTreme EFIS-G3 - frozen display
- Replies: 4
- Views: 1257
Re: XTreme EFIS-G3 - frozen display
Hi Moshe,
Please load V3.07 onto the "good" unit and lets see if it freezes (Maybe some sort of setting or installation issue). On the "frozen" unit, reload V3.07 and load default settings (This will default all settings to factory defaults).
Regards,
Franz
Please load V3.07 onto the "good" unit and lets see if it freezes (Maybe some sort of setting or installation issue). On the "frozen" unit, reload V3.07 and load default settings (This will default all settings to factory defaults).
Regards,
Franz