Search found 33 matches
- Wed Jan 27, 2021 1:34 am
- Forum: EFIS Systems
- Topic: Alarm Acknowledge
- Replies: 11
- Views: 6913
Re: Alarm Acknowledge
Hi I set up a alarm light on my panel. Hooked to the output O5 on the Analog/digital 25 pin connector. The light comes on when I turn on the system. The problem is it won't turn off. I always get an alarm about low voltage every time I boot up so I press the acknowledge alarm on the efis but the lig...
- Wed Nov 18, 2020 5:17 pm
- Forum: EFIS Systems
- Topic: SP-7 LED
- Replies: 2
- Views: 2068
Re: SP-7 LED
Thanks Ranier
I bought both of these in 2020, so your saying the SP7 is an older model? (with red LED) ,How old would it be ?
I bought both of these in 2020, so your saying the SP7 is an older model? (with red LED) ,How old would it be ?
- Wed Nov 18, 2020 1:30 am
- Forum: EFIS Systems
- Topic: SP-7 LED
- Replies: 2
- Views: 2068
SP-7 LED
I noticed today that my SP-6 has a blinking green LED and the SP-7 has a blinking red LED. Is this normal?
- Tue Nov 17, 2020 3:53 pm
- Forum: EFIS Systems
- Topic: Calibration of Challenger Touch Screen
- Replies: 4
- Views: 2827
Re: Calibration of Challenger Touch Screen
But that was one of the main selling points. The video shows you have to push like a button. Mine is way too sensitive. Haven't flown with it yet but I can tell It's going to be hard not to touch something else. Ya'll (yes I'm a Texan) need some updated info on your products. At least you solved tha...
- Tue Nov 17, 2020 5:39 am
- Forum: EFIS Systems
- Topic: Calibration of Challenger Touch Screen
- Replies: 4
- Views: 2827
Calibration of Challenger Touch Screen
I'm cannot calibrate my touchscreen on the Challenger. there is no menu item that I can find and referenced in the installation manual. And none of the rotary knobs have push detents to hold down while powering on as referenced in the installation manual. So what give here. How do I get into the cal...
- Thu Nov 12, 2020 12:53 am
- Forum: EFIS Systems
- Topic: Manuals
- Replies: 1
- Views: 1724
Manuals
Where can you find the manuals for the G3 Challenger. The menus that I have downloaded for some things are not the same as the menu in my Challenger G3. Like the magnetic current sensor. I have it connected to RDAC #2 but I cannot find any way to do that in the menu. There are other things that I'm ...
- Tue Nov 10, 2020 3:48 am
- Forum: EFIS Systems
- Topic: Alarm Acknowledge
- Replies: 11
- Views: 6913
Re: Alarm Acknowledge
Ok thanks ford that info. I have a lot to learn.
- Mon Nov 09, 2020 2:14 am
- Forum: EFIS Systems
- Topic: Alarm Acknowledge
- Replies: 11
- Views: 6913
Re: Alarm Acknowledge
One more thing. I went through the setup in the SIM and I can't find a setting for Auto pilot disconnect. I see Autopilot 180, Autopilot Wings Level, etc. But no Disconnect. ????"
- Sun Nov 08, 2020 3:12 pm
- Forum: EFIS Systems
- Topic: Alarm Acknowledge
- Replies: 11
- Views: 6913
Re: Alarm Acknowledge
Hi I'm a little challenged when it comes to this electronic stuff. So if I'm getting this all the grounds from the grip for say , flip flop of radio, alarm acknowledge, autopilot disconnect, all go to the analog input 25 pin connector? And you set them up in the EFIS? How much does the resistor drop...
- Sun Nov 08, 2020 3:56 am
- Forum: EFIS Systems
- Topic: Alarm Acknowledge
- Replies: 11
- Views: 6913
Alarm Acknowledge
Hi
I'm installing Infinity Aerospace grips in my 801. I have a Challenger Efis. How do I connect a button on the grip to cancel alarms on the EFIS. I can find how to connect a light for the alarm but not how to acknowledge it remotely.
I'm installing Infinity Aerospace grips in my 801. I have a Challenger Efis. How do I connect a button on the grip to cancel alarms on the EFIS. I can find how to connect a light for the alarm but not how to acknowledge it remotely.