Search found 37 matches
- Mon Jul 31, 2023 2:52 pm
- Forum: EFIS Systems
- Topic: MX1 SD card formatting
- Replies: 2
- Views: 1999
MX1 SD card formatting
Hello All. I have had no luck getting my MX1 to mount any SD card other than the one that came with the EFIS. I have simply formatted other cards as FAT/FAT16 using a couple of PC options yet I always get a failed-to-mount message on the MX1. Is there a specific format/procedure that I should be usi...
- Sat Jun 03, 2023 10:19 am
- Forum: MGL Radio frequency products
- Topic: V16 high VSWR
- Replies: 2
- Views: 6760
Re: V16 high VSWR
For a VSWR so bad, one would expect a cable fault. I assume that you've checked for short circuit between signal and screen conductors, and open circuit faults too?
Are you adapting from one cable type to another? Or in other words, how are you adapting from SMA to BNC?
Are you adapting from one cable type to another? Or in other words, how are you adapting from SMA to BNC?
- Fri May 12, 2023 1:02 pm
- Forum: Technical - floobidust
- Topic: MGL auto pilot
- Replies: 2
- Views: 5363
Re: MGL auto pilot
They are serial data ports so any servo would need to be RS232 equipped. What type of servo are you connecting??
- Fri May 12, 2023 9:59 am
- Forum: MGL Radio frequency products
- Topic: Sidetone echo
- Replies: 3
- Views: 6311
Re: Sidetone echo
Can I suggest that you check that your microphone gain is set appropriately. I was surprised by how much attenuation I needed on my V16 to get the audio paths stable. There's a procedure (in the manual I believe) about matching the sidetone volume of your voice to the comms volume. If your own voice...
- Sun Mar 19, 2023 10:02 am
- Forum: MGL Radio frequency products
- Topic: v6 Transmit problems on certain frequencies
- Replies: 2
- Views: 5568
Re: v6 Transmit problems on certain frequencies
I have a V16. I don't know whether the gain structure and processing is the same as a V6, but this may help. By default, the microphone input gains were way too high for both A20 and David Clark and the comms were almost unuseable. Currently, my input gains are -4.75dB and I feel that I can certainl...
- Wed Feb 08, 2023 9:14 pm
- Forum: EFIS Systems
- Topic: Pitot/static ports
- Replies: 2
- Views: 1580
Re: Pitot/static ports
Thanks for the response...
I'll have to try again, but I know that the tubing itself was airtight. It could only be the union of pipe-to-port or the port itself, but the pipe did seem to fit tightly to the port stem.
I'll try some softer silicone tube....
I'll have to try again, but I know that the tubing itself was airtight. It could only be the union of pipe-to-port or the port itself, but the pipe did seem to fit tightly to the port stem.
I'll try some softer silicone tube....
- Wed Feb 08, 2023 7:52 pm
- Forum: EFIS Systems
- Topic: Pitot/static ports
- Replies: 2
- Views: 1580
Pitot/static ports
Does anyone know if the pitot and static ports on EFIS's (any model) are airtight? Sounds like a stupid question but I was using a U-gauge manometer to check the accuracy of a steam gauge ASI and found that it leaked pressure. I then tried the same test and found that all the ports on an MX1 leaked ...
- Fri Oct 28, 2022 6:14 pm
- Forum: EFIS Systems
- Topic: ECB power-up problem
- Replies: 0
- Views: 2615
ECB power-up problem
I have an MGL ECB (linked to MX1) controlling most of my electrical equipment and have a query about operation on boot up. I've installed toggle switches with bi-colour LEDs for all 8 switching channels. Everything seems fine except for 2 behavioural issues: 1. If any switches are set to 'ON' within...
- Mon Oct 24, 2022 8:45 pm
- Forum: EFIS Systems
- Topic: Trig interface LED error status
- Replies: 2
- Views: 1329
Re: Trig interface LED error status
...perhaps I should have said 'don't all shout at once'...
A firmware update on the MGL/Trig interface seems to have resolved this, just in case anyone else suffers the same.
Many thanks to Paul at parts4aircraft for pointing me to this.
A firmware update on the MGL/Trig interface seems to have resolved this, just in case anyone else suffers the same.
Many thanks to Paul at parts4aircraft for pointing me to this.
- Mon Oct 24, 2022 8:41 pm
- Forum: EFIS Systems
- Topic: Help with Screen Creation MX1
- Replies: 8
- Views: 3572
Re: Help with Screen Creation MX1
You appear to have hijacked an unrelated thread not relavant to your issue.
Assumiung that "eephus" means EFIS, have you enabled the equipment/devices in the system setup menu?
Red crosses will appear in icons/windows of devices that are not eneabled even if connected and powered correctly.
Assumiung that "eephus" means EFIS, have you enabled the equipment/devices in the system setup menu?
Red crosses will appear in icons/windows of devices that are not eneabled even if connected and powered correctly.