Search found 48 matches
- Mon Oct 10, 2022 3:28 am
- Forum: EFIS Systems
- Topic: Enigma heading fluctuations
- Replies: 4
- Views: 1711
Re: Enigma heading fluctuations
What Magnetic Sensor are you using and where/how is it mounted?
- Sun Sep 04, 2022 5:44 pm
- Forum: EFIS Systems
- Topic: Tach, hobbs, maint
- Replies: 1
- Views: 1340
Re: Tach, hobbs, maint
The HOBBS timer is the actual Engine running time. It emulates an Electric HOBBS Clock. Set the HOBBS Minimum RPM to half your idle speed to time whenever the engine is running. The TACH Timer Speed varies in Proportion to the Engine RPM. It emulates Old-School Tachometer timers that displayed Total...
- Fri Sep 02, 2022 2:17 am
- Forum: EFIS Systems
- Topic: Design Item to display Aircraft's Gross Weight
- Replies: 4
- Views: 2209
Re: Design Item to display Aircraft's Gross Weight
If you set up the Weight and Balance calculator it will Display your current Weight along with your Weight with Full and Empty Fuel.
- Tue Aug 30, 2022 8:32 pm
- Forum: EFIS Systems
- Topic: XTreme EFIS/EMS Gen 1 or Gen 2?
- Replies: 1
- Views: 1004
Re: XTreme EFIS/EMS Gen 1 or Gen 2?
To find what firmware you are using have a look at your ...
Menu > Information System > System Status >
You should find a line similar to " iEFIS G2 version A 1.0.0.1 "
Your menu tree may differ but this should get you started.
Menu > Information System > System Status >
You should find a line similar to " iEFIS G2 version A 1.0.0.1 "
Your menu tree may differ but this should get you started.
- Tue Aug 30, 2022 8:16 pm
- Forum: EFIS Systems
- Topic: Odyssey backup battery
- Replies: 2
- Views: 1437
Re: Odyssey backup battery
Fuses exist to protect the wiring. Not the device. Assuming you power the EFIS and RDAC with 18 AWG wire. 18AWG is rated at 10 amps at 60°C. A 5.0 amp fuse would be more than sufficient in this situation. The EFIS to RDAC wire would not necessarily need an additional fuse. But if you insisted, anoth...
- Mon Aug 29, 2022 5:35 pm
- Forum: EFIS Systems
- Topic: Fuel Level Alarm - Missing Enables
- Replies: 4
- Views: 1788
Re: Fuel Level Alarm - Missing Enables
I just upgraded my G3 Firmware to v.1.1.2.1 hoping maybe it would help. No Such Luck. Can anyone running G3 software on any iefis lite confirm that the Low Fuel Alarm works? I am not asking if the Bargraph turns RED on low fuel. I am asking if the Alarm Field above the Bargraph also turns RED and th...
- Wed Aug 24, 2022 2:34 am
- Forum: EFIS Systems
- Topic: Inflight transponder squawk change
- Replies: 4
- Views: 1580
Re: Inflight transponder squawk change
On the 8-inch and larger iefis models, the 12 Physical Buttons on the bottom can be used to enter numbers when the Xpndr or Radio is selected. The Discover Lite does not have those buttons but it does have 8 equivalent Virtual Buttons that normally display AP, NAV, CHECK, MAP, ETC. along the Left ed...
- Tue Aug 23, 2022 10:13 pm
- Forum: EFIS Systems
- Topic: Inflight transponder squawk change
- Replies: 4
- Views: 1580
Re: Inflight transponder squawk change
Do your Big Buttons at the Side of your display become 0-7, Etc.
You may also get a similar set of buttons when operating the Radio.
A much easier target for our fat-shaky fingers.
You may also get a similar set of buttons when operating the Radio.
A much easier target for our fat-shaky fingers.
- Sat Aug 20, 2022 10:15 pm
- Forum: EFIS Systems
- Topic: Fuel Level Alarm - Missing Enables
- Replies: 4
- Views: 1788
Re: Fuel Level Alarm - Missing Enables
Thanks, Jim, That actually helps. It is not so much that you have a Voyager vs. my Explorer, as much as you are running G2 vs. my G3 firmware. I have discovered that along with the Fuel Level Alarm not working, the Fuel Flow Alarm also does not work, while the Fuel Pressure Alarm Works just fine. Co...
- Fri Aug 19, 2022 10:10 pm
- Forum: EFIS Systems
- Topic: Fuel Level Alarm - Missing Enables
- Replies: 4
- Views: 1788
Re: Fuel Level Alarm
Can anyone confirm that an ALARM FIELD attached to FUEL LEVEL1, RDAC 1 ALARM operates in their iEFIS as expected?
I need to know if there is a system problem or if it is just that I have it configured incorrectly.
I have tried deleting and rebuilding the Alarm to no avail.
Thanks, Bill.
I need to know if there is a system problem or if it is just that I have it configured incorrectly.
I have tried deleting and rebuilding the Alarm to no avail.
Thanks, Bill.