The Weight and Balance Icon has the options (Checkboxes) to "Show by Icon Holder Click" or "Show If Route Active".
Checking either box causes the Icon to be unselectable as if it were hidden but it still remains visible. It never becomes hidden.
Search found 48 matches
- Thu Feb 23, 2023 12:00 am
- Forum: EFIS Systems
- Topic: Weight and Balance Functional Icon
- Replies: 0
- Views: 3038
- Tue Feb 21, 2023 7:25 am
- Forum: General
- Topic: Fuel pressure sensor
- Replies: 2
- Views: 4499
Re: Fuel pressure sensor
Have you configured all the settings properly?
Menu>System Setup>Fuel Related Setup>Setup RDAC1 Senders>Fuel Pressure Setup
It sounds like the system thinks 5 volts = 7psi instead of 70psi.
Also, confirm your sender is 0.0-5.0v and not the more common 0.5-4.5v; it makes a difference.
Menu>System Setup>Fuel Related Setup>Setup RDAC1 Senders>Fuel Pressure Setup
It sounds like the system thinks 5 volts = 7psi instead of 70psi.
Also, confirm your sender is 0.0-5.0v and not the more common 0.5-4.5v; it makes a difference.
- Mon Feb 20, 2023 7:37 pm
- Forum: EFIS Systems
- Topic: G-Force Meter Reset
- Replies: 0
- Views: 2785
G-Force Meter Reset
When the G-Forces are reset, the MAX is reset to 1.0 as expected, but the MIN is reset to 0.0. This causes the MIN to only register Negative G's and never register any positive values below +1.0. Negative G's in an Autogyro is a non-recoverable Fatal event. Getting light in the seat and especially l...
- Mon Feb 20, 2023 7:19 pm
- Forum: EFIS Systems
- Topic: Send a GPS-NMEA 0183 via RS232
- Replies: 4
- Views: 2519
Re: Send a GPS-NMEA 0183 via RS232
I am pretty sure I matched the baud rates, but I'll Check it again.
Thanks.
Thanks.
- Mon Feb 20, 2023 7:13 pm
- Forum: EFIS Systems
- Topic: Global Screen File Names
- Replies: 2
- Views: 1543
Re: Global Screen File Names
Thanks, Rainier,
I missed the part where this was only applicable to the Default File System.
I missed the part where this was only applicable to the Default File System.
- Sun Feb 19, 2023 12:22 am
- Forum: EFIS Systems
- Topic: Global Screen File Names
- Replies: 2
- Views: 1543
Global Screen File Names
The Alteration Guide describes creating custom screen files without page numbers that all screens load by default. The Fuel and Engine screens are common to most pages. I currently have to create Engine1.sdf, Engine2.sdf, Engine3.sdf, etc as all identical copies. I have tried creating screen files t...
- Sun Feb 19, 2023 12:04 am
- Forum: EFIS Systems
- Topic: Send a GPS-NMEA 0183 via RS232
- Replies: 4
- Views: 2519
Re: Send a GPS-NMEA 0183 via RS232
In theory, by using ...
Menu>System Setup>Serial Port Routing
You can define a serial port as a "GPS NEMA Port"
I have tried to use this to send location data to my ELT but have not been successful.
I would also like to know if anyone has made this work.
Menu>System Setup>Serial Port Routing
You can define a serial port as a "GPS NEMA Port"
I have tried to use this to send location data to my ELT but have not been successful.
I would also like to know if anyone has made this work.
- Sun Dec 18, 2022 1:46 am
- Forum: EFIS Systems
- Topic: 3D terrain does not show red
- Replies: 1
- Views: 1275
Re: 3D terrain does not show red
Check your setting under Menu > System Setup > Terrain Warning.
This only works if the GPS is ON and actively Tracking Satellites.
So, it may not work inside a hanger.
This only works if the GPS is ON and actively Tracking Satellites.
So, it may not work inside a hanger.
- Sat Nov 26, 2022 5:55 am
- Forum: EFIS Systems
- Topic: Design/simulator 1.1.2.2
- Replies: 5
- Views: 2047
Re: Design/simulator 1.1.2.2
251 is the Max possible airspeed.
This tells me that the "Dynamic Pressure" Slider (the middle one) on the "Pressure Sensor Simulation" Window is Maxed out.
Set it to the Bottom for Zero.
Set it to about 10% for typical GA Airspeeds.
This tells me that the "Dynamic Pressure" Slider (the middle one) on the "Pressure Sensor Simulation" Window is Maxed out.
Set it to the Bottom for Zero.
Set it to about 10% for typical GA Airspeeds.
- Thu Nov 17, 2022 4:37 am
- Forum: EFIS Systems
- Topic: Design/simulator 1.1.2.2
- Replies: 5
- Views: 2047
Re: Design/simulator 1.1.2.2
Are you getting no response from the sliders; or do you see "X"s over the gauges?
Sorry if I am stating the obvious, but have you clicked the RDAC ON/OFF button at the upper Left?
Sorry if I am stating the obvious, but have you clicked the RDAC ON/OFF button at the upper Left?